Skip to content

Lights, Strobes, and Lighting Technique / Archived topic

Ikelite Manual Controller Problem?!?!

Started by Detonate ·

  • 13Posts
  • 13Replies

Read-only discussion

Ikelite Manual Controller Problem?!?!

13 posts
  1. Ikelite Manual Controller Problem?!?!

    Well I had me a nice malfunction on my recent trip. :D Maybe someone can help explain.

     

    I have a D70 with dual Ike DS125's with 2 manual controllers. I tested everything topside and it was working fine.

     

    On the first dive, I took the first photo, and then I could hear one of my strobes beeping at me. I looked over at it, and it was constantly firing.

     

    I turned it off and on again, and tried another test shot. Same thing. It started beeping and non-stop firing.

     

    I tried different combinations of one strobe off and one on, and ultimatley gave up, as I couldn't get either strobe to fire with the other turned off, and with both of them on I got the beeping and non stop firing.

     

    I quadloople checked that both strobes were in TTL mode connected to the controler. I made sure that the manual controllers were actually set to a number, and not in between 2 numbers, or pointing to the clicks that aren't settings at all.

     

    I tried both strobes in manual mode and still could get them to fire while connected to the manual controllers.

     

    After the dive I just removed the manual controllers from the rig, and did the rest of the weeks diving with the strobes direct connected and set to 1/2 power.

     

    I assumed that something must be wrong with my manual controllers, but what was really strange, is that my friend that was with me, who dives an identical rig, had the EXACT same problem on dive 2.

     

    Any idea what could be wrong? I'm thinking it's got to be something I set up in my camera that is causing it.

     

    I checked my camera settings to make sure the flash was set in normal flash mode, no red eye, no rear curtain, etc...

     

    I checked to make sure exposure compensation was set at zero...

     

    Not sure what else it could be...

     

    -Jim March

  2. Jim, any chance that the sensor was being triggered by sunlight?....I tape over the sensors on each controller so that they don't react to other divers's strobes or to sunlight

     

    Karl

  3. Hmmmm, I didn't think about that at the time.

     

    I do remember one of the black caps not being on one of the controllers when packing, but I'm pretty sure it was on there during the dive.

     

    Also, the strobe would not start continuously firing until I tried to take a picture.

     

    i.e. I would turn the firing strobe off and then on again, then take a test shot of the ground while watching the strobes to make sure they were working, and as soon as I'd take the shot, it would start to beep and continuously fire....

     

    You theory is possible though, as I don't remember with 100% certainty that the sensor cap was on the controller.... Hmmm....

  4. I'd still ask Ikelite, as it sounds like you were deep enough that sunlight wouldn't be intense enough to trigger the strobes

     

    I'll be interested when you figure it out....

     

    Did you have your sync cords connected correctly? Red band to right strobe?

     

    Karl

  5. Did you have your sync cords connected correctly? Red band to right strobe?
    I remember thinking at the time... "Aren't these colors supposed to be connected to a specific strobe???", but then I thought.... "How the hell does this cord know left from right anyways!"

     

    Doesn't that only matter if I want to turn off 1 strobe and still have the second strobe fire? I tried turning each one off to see if the other would fire solo with no luck.

  6. Doesn't that only matter if I want to turn off 1 strobe and still have the second strobe fire? I tried turning each one off to see if the other would fire solo with no luck.

     

    I think you may be right about this Jim :shock:

     

    Let me know what Ikelite says...we're heading to Cozumel for a week next Nov.12 and want to know what to do it it happens to me :D

     

    BTW, how was your trip.....pics?

     

    Karl

  7. Trip was great. It was a bigger pain than I anticipated being on a cruise and hitting 3 dive locations in 3 days.

     

    I shot nothing on the first dive in Cozumel, and then shot the 60mm the next 2 dives.

     

    I shot the 12-24 on the first dive in Roatan, but then remembered how much I suck at wide angle photography and then switched back to the 60mm.

     

    In Belize I asked the operator what he thought would be better, Macro or Wide Angle, and he suggested macro, so I again shot the 60mm on both dives in Belize.

     

    Cozumel currents were ripping when we were there. Every dive was ride for sure. We dropped down on dive 2 and found a Green Moray hiding from the current under a ledge that was about as tall as me, and his body was thicker than my legs. Unfortunately the last 2 divers off the boat while dropping down got snatched by the current and ended up about 1/2 mile from the boat. They surfaced and blew their whistle until another dive boat found them. By the time our dive boat picked them up and got back to our bubbles, the DM already had the Safety Sausage inflated, so they did not rejoin the dive.

     

     

    There was a slight, but very noticeable surge in Roatan that made shooting macro a difficult. Visibility was in the 50-60 ft range. Not nearly as nice as the vis I'm used to in Cozumel. There seemed to be more life on the reefs, and it was very cool that the top of the wall was only about 10 ft of water. They literally let us breath our tanks dry with no safety stop needed. Very cool. The dive masters did kind heard us around though, which made hunting for photo opportunities a little difficult, and I never felt like I had enough time to get the shot I wanted.

     

    Belize was very awesome. I'd say it was my favorite. The Dive boat picked us up at our anchored cruise ship, and the boats where very fancy, and fast. According to my GPS they traveled at about 26 MPH and you couldn't even feel it. It was a 45 minute boat ride to the atoll we dove. The coral wasn't as impressive as Cozumel, but the amount of life the reefs had were amazing. Although I shot macro both dives, thinking back I wish I would have shot Wide angle.

     

    It seems like 90% of all of my pictures are of Blennies or Christmas Tree worms. Pretty disappointing really.

     

    I shot in Basic + RAW mode, so I plan on doing a Mass resize on the JPEGs, sorting through the ones that catch my attention, and uploading them un-retouched this evening.

     

    I'll post a link in the Photo Showcase once I'm done.

  8. Autofiring is almost always caused by water in sync system. Sounds like leaking EV Manual Controller since removing it allowed the system to operate............

  9. Ok, now I'm thinking it may be my Sync cord?!

     

    I setup everything with both Manual Controllers. Nothing worked.

     

    Eventually I got it working with one manual controller connected to Red Marked side of the dual sync cord, and the second strobe directly connected to the sync cord.

     

    Next I tried using that same manual controller on the other end of the sync cord. Nothing worked.

     

    So I switched it back to having the manual controller on the side marked red, but this time I used the other manual controller. Everthing worked.

     

    So basically, the side with no Red or Blue tape has to be directly connected to the strobe, and the side with the Red tape works with both manual controllers, and also obviously directly connected as well...

  10. Time for FedEx ride to Indianapolis :D

     

    Karl

  11. Suggest you make sure you have the 2 internal switches on your manual controllers properly set before you send the controllers in. I had similar problems despite having checked the switches several times. After giving up on everything I checked the internal switches and one had somehow been slightly displaced. It looked like it was in the right place but wasn't completely pushed over. Correcting this solved all my problems.

  12. Thanks for the suggestion. That was actually the first thing I checked, becasue I was mainly checking to see if they flooded.

     

    I have discovered a small tear in the rubber on the sync cord, near the "blue" end that connects to the housing. I can see a red wire inside.

     

    I'm pretty sure that water getting in there is what is causing the problem, but I'm still uncertain as to why it doesn't work topside, or why I can use a manual controller on the "red" side, or why both strobes work when directly connected to the sync cord.

     

    Logic would suggest that if the cord was flooded, it just plain wouldn't work.

     

    At anyrate, I'm going to ship it back to Ike to have a look see.

  13. Jim, My 2 cents. Buy a new dual sync cord, set your strobes to 1/2 power and forget about the manual controllers. I recommend this because I think using dual manual controllers introduces too many variables when shooting and they are one more thing to break. Then upgrade to iTTL when Ike makes it available.

     

    In the meantime, consider streamlining your rig by getting rid of the posts for the manual controllers.

     

    Anyway that's what I'm doing.

Ultralight Control Systems

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.