A big advantage of the Kraken bulkhead over the Nauticam one is that the Kraken is compatible with a higher number of Nauticam housings than the Nauticam plug because the cable on the Nauticam is not removable and the one on the Kraken is which makes a huge difference in favor of Kraken.

I experienced this on the NA-GH5: the 90° USB-C plug simply won't go through the M16 port while on other housing like NA-Z8, it inserts well into the M16. The difference on the housing is just the thread length on the NA-GH5 that is longer than its equivalent on NA-Z8. I wish Nauticam has made a bulkhead with a removable cable. I've solved this issue on the NA-GH5 by using Kraken bulkheads. With the proper adapter (like I it), you can even fit it on a M14 port.

14 hours ago, OneYellowTang said:

@Dave_Hicks

It might just be me ;)

I religiously change the battery in my Z-8 after each morning of 2 dives. I can stretch i to 3, but at that point I might miss a few shots at the end of a dive. I also always change before going black water diving.

With the various updates I have noticed the battery draw getting better, however not to the point I'm trying 4 dives on a single charge. With the ENL-15C battery my older D850 can shoot multiple days without concern (my son is shooting with this camera now).

Do you use the EVF exclusively, or do you use the back screen? And do you have the camera in Airplane Mode? I also rotate between 3 batteries to reduce wear.

I only use the EVF, which I suspect uses less power than the rear screen. And no need for wifi/bluetooth underwater. Even shooting some video for a few minutes across dives, I've still only run down the Z8 to zero once in about 300 dives with it to date. I was stretching it out on a 4-dive day and had several rapid action encounters were I really racked up the shutter count.

Nice idea for my a7V Nauticam housing.

Just still need the same for my s-TURTLE 3 SMART TTL trigger and housing can stay closed forever :)

Has anyone experience on the turtle trigger battery duration ?

I have still only a few dives with the setup, so difficult to figure out...

I'm likely getting the Kraken M16 so I can just leave my housing under vacuum for most of a trip. As I've found recently though the Nauticam leak sensor will rip through a set of batteries in a few days if left on.

I am thinking perhaps of a magnetic reed switch to allow it to be turned on and off without opening the housing?

14 hours ago, FrancoisC said:

Has anyone experience on the turtle trigger battery duration ?

I have the same trigger and it last for a long time. I use manual and not sure on the power setting (fairly low i guess), but i did like one week in a resort (3 dives per day) and the led flashed still over 75%.

Using TTL or max power probably uses more.

4 hours ago, Grantmac said:

I'm likely getting the Kraken M16 so I can just leave my housing under vacuum for most of a trip. As I've found recently though the Nauticam leak sensor will rip through a set of batteries in a few days if left on.

I am thinking perhaps of a magnetic reed switch to allow it to be turned on and off without opening the housing?

My new one uses also way more battery compared to previous (NA-A1ii vs. NA-A7RV). But i dont think magnetic switch for power works, i think the circuit needs to sense vacuum forming, instead of just turning on with vacuum already there.

I might be wrong of course.

18 minutes ago, Sokrates said:

I have the same trigger and it last for a long time. I use manual and not sure on the power setting (fairly low i guess), but i did like one week in a resort (3 dives per day) and the led flashed still over 75%.

Using TTL or max power probably uses more.

My new one uses also way more battery compared to previous (NA-A1ii vs. NA-A7RV). But i dont think magnetic switch for power works, i think the circuit needs to sense vacuum forming, instead of just turning on with vacuum already there.

I might be wrong of course.

He would have to release vacuum and then turn the switch off. Upon rearming the circuit with the "switch" of some sort he envisages then restore the vacuum. But he would not have to open the housing.

I just open my housing in the evening, give everything a once over and then close it back for the next day and pull vac about 30 minutes before departure or when convenient. But, I recharge between dives or at lunch as needed without having to open the housing on the boat or a sandy beach or some other undesirable place.

45 minutes ago, Nemrod said:

He would have to release vacuum and then turn the switch off. Upon rearming the circuit with the "switch" of some sort he envisages then restore the vacuum. But he would not have to open the housing.

I just open my housing in the evening, give everything a once over and then close it back for the next day and pull vac about 30 minutes before departure or when convenient. But, I recharge between dives or at lunch as needed without having to open the housing on the boat or a sandy beach or some other undesirable place.

Alternatively leave it on for a day or two and then turn off without releasing vacuum it should continue to hold.unless you do something like drop the housing or otherwise subject it to load. I think the vaccum valve from leak sentinel is designed to allow you turn it off.